XTOOL AnyToyo SK1 Toyota Smart Key Emulator

XTool AnyToyo SK1 is a data collector, as well as a smart key emulator, allowing you to do a key cloning process in add key / all keys lost situations for 2013+ Toyota models with the smart key. AnyToyo SK1 can also do an emergency start when there is no key available on your hand and generate new keys using AnyToyo smart key that comes with the set.

Product Introduction:
AnyToyo Toyota 4A/8A smart key data collector & emulator. With this collector, an
XTOOL tablet, Internet connection and a KC501 key programmer, you can generate an emulated Toyota 4A/8A
smart key without searching for pincode, which could be used for emergency ignition or act as an original key in
order to add keys when there are no original keys available. With our programmable keys, you can also generate
a 4A/8A smart key which is matched on this car without searching for pincode or connecting to the module.
The emulated data will be erased from the emulator once it is disconnected to XTOOL devices.
① Antenna: Used to collect data and emulate key data.
② Light: When connected, the green light will be turned on.
When collecting data, the green light will flicker, then goes off once it is done
collecting.
③ USB 3.0 Port: Used to connect to the XTOOL devices.
When using XTOOL tablets with Type-C ports, please connect the USB3.0 to
Type-C adapter before use.

How to Use
1. Collecting data from start/stop button:
· Connect emulator to the tablet and start the process
· When the notice pops up from the tablet, put the antenna close to
the start button
· The light will flicker when collecting and goes off when finished
collecting
2. Collecting data / emergency start from low-frequency antenna:
· The antenna usually locates at:
1） At the front, beneath the armrest storage area
2） In the middle, under the backseats
3） Door handle (for models with keyless entry)
· Connect emulator to the tablet and start the process
· When the notice pops up from the tablet, put the antenna
close to the low-frequency antenna
· The light will flicker when collecting and goes off when finished collecting
· After collecting data, put the emulator close to the antenna and press the start button to do an
emergency start.
Support List
Note: The chip information shown on the list may vary in different markets or models. The list is for reference only.
Model Model year Chip type PCB Number
TOYOTA
Alphard 2017.1+ 8A-85 0120
Avalon 2019.1+ 8A-88 0410
Camry 2018.1+ 8A-88 0410
2018-2021 8A-85 0351
Corolla 2019-2021 4A 2000
C-HR 2018.1+ 8A-88 0410
C-HR (US) 2018-2021 8A-85 0010
Crown 2018.1+ 8A-82 2110
Highlander 2018.1+ 8A-82 2110
Land Cruiser
2017.1+ 8A-82 F43
2018-2019 8A-82 2110
2020-2021 8A-85 0010
Land Cruiser Prado 2018.1+ 8A-82 3330
Levin 2019-2021 4A 2000
Prius 2018.1+ 8A-88 0410
2016-2021 8A-85 0351
RAV4 2019.7+ 8A-88 0410
2019-2020 8A-85 0351
Vellfire 2017.1+ 8A-85 0120
Wildlander 2019.1+ 8A-88 0410
LEXUS
ES 2018.1+ 8A-88 0440
GS 2018.1+ 8A-88 0440
IS 2017.1+ 8A-82 2020
LS 2018.1+ 8A-88 0440
NX 2018.1+ 8A-82 2110
RX 2018.1+ 8A-85 0010
UX 2018.1+ 8A-88 0440
GS 2018.1+ 8A-88 0440